AutoTran "Outside seal kit" The below parts marked with a * are included in it, if applicable to your year. Picture
of the parts listed below |
|||
Illustration No. |
Description |
Rebuilding Kit |
Overhaul Kit |
1 |
Clutch Drive Friction Plates (Internal Lugs, 1950-55 or Internal Splines, 1956-62) |
4 |
0 |
2 |
Clutch Driven Steel Plates (Six External Lugs) 1950-55 small hole, 1956-62 large hole |
5 |
0 |
3 |
Case to Housing Gasket (Valve Body Gasket) (1950-52, 53-54, E55, 55-57, 58 or 59-62) |
1 |
1 |
4* |
Side Cover Gasket (Right & Left) |
2 |
2 |
Not Illustrated* |
Servo Cover Gasket, 1950-54, 1955-57 or 1958-62 |
1 |
1 |
7 |
Valve Body to Case Gasket "Banana Gasket" Kit, Square O'Ring Replacement Style, 1950-57 or 1958-62 |
1 |
1 |
8 |
Rear Pump Gasket |
1 |
1 |
Not Illustrated |
Rear Oil Pump Drive Pin (1955-62 only) |
1 |
1 |
9* |
Governor Cover Gasket (1953-62 only) |
1 |
1 |
Not Illustrated* |
Modulator Housing Gasket (1950-54 only) |
1 |
1 |
11 |
U-Joint Seal (1950-54 only - Not Corvette - See 13a) |
1 |
1 |
12 |
U-Joint Ball Seal (1950-54 only - Not Corvette) |
1 |
1 |
Not Illustrated |
U-Joint Shim Gaskets (1950-54 only - Not Corvette) |
4 |
4 |
13 |
Extension Seal – Metal Clad (1955-62 only) |
1 |
1 |
13a |
Extension Seal – Metal Clad (1953-55, 6 Cylinder Corvette only) N#452352 |
1 |
1 |
14 |
Front Pump Seal - Metal Clad (1950-52 or 1953-62) |
1 |
1 |
14a |
Front Pump Seal - Metal Clad - Double Lip Style, 1953-62 only |
available (add on $2.00) |
available (add on $2.00) |
15* |
Oil Supply Pump Suction Seal |
1 |
1 |
16* |
Manual Lever Lip Seal |
1 |
1 |
17 |
Torque Converter "O" Ring, 1950-52 or 1953-62 (Used with a split converter only) Both are "square cut" o'rings |
1 |
1 |
18 |
Case Extension "0" Ring |
1 |
1 |
19 |
Front Pump "0" Ring |
1 |
1 |
20* |
Oil Filler Tube "0" Ring |
1 |
1 |
21 |
Piston Lip Seal - Inner |
1 |
1 |
22 |
Piston Lip Seal - Outer, 1950-52 or 1953-62 |
1 |
1 |
Not Illustrated* |
Speedometer Gear (Bullet) "0" Ring - 1955-62 only |
1 |
1 |
Not Illustrated* |
Speedometer Gear to Housing (Bullet) O'Ring - 1955-62 only (It's a Orange Silicon O'Ring - OEM P/N 584059) |
1 |
1 |
Not Illustrated* |
Reverse Booster Valve Guide Seal - 1955-57 only |
1 |
1 |
Not Illustrated* |
Booster Valve Sleeve "0" Rings - 1958-62 only |
2 |
2 |
Not Illustrated |
Turbine Bolt Seal "0" Ring - 1950-52 only |
1 |
1 |
Not Illustrated |
Torque Converter Hub O'Ring - 1950-52 only |
1 |
1 |
Not Illustrated* |
Throttle Valve Lever Shaft Seal - 1955-62 only (1163928) |
1 |
1 |
Not Illustrated* |
Throttle Valve Low & -Drive Body End Plate Gasket - 1953-54 or 1955-62 |
1 |
1 |
Not Illustrated* |
Lever & Drive Valve Body Gasket - 1958-62 only (not used in 1950-52 or 1953-57) |
1 |
1 |
28 |
Input Shaft Sealing Ring 1" Hook |
1 |
1 |
29 |
Governor Sleeve Sealing Ring 1" Hook - 1953-54 only |
3 |
3 |
30 |
Clutch Drum Sealing Ring 2" Hook |
2 |
2 |
Not Illustrated* |
Valve Spring Plug Gasket - 1950-54 only |
1 |
1 |
Not Illustrated |
Vacuum Modulator Diaphragm, 1950-54 Not Included #3709049 (8510) |
available ($35.00) |
available |
Not Illustrated |
Vacuum Modulator w/Screw in Threads, 1958-62 Not Included #3745169 (8738) |
available ($44.00) |
available |
Not Illustrated |
Low Servo Piston Sealing Ring, 1950-54, 1/8" X 3¼" or 1955-62 1/8" X 2 3/4" - Not Included as rarely needed |
available ($3.00) |
available |
Not Illustrated |
Reverse Servo Piston Sealing Ring, 1950-62, 1/8" X 3¼" - Not Included (Same as 1950-54 Low Servo Ring) Note: $5.00 for both rings |
available ($3.00) |
available |
The above parts, marked with a *, are included in the "Outside seal kit" if applicable to your year.
Click here for complete ordering information
I am not setup to take credit cards directly, for
information
for paying by
Visa, MasterCard, Discover or American Express click on
PayPal
below.
I accept PayPal
for any size order
(there is no additional cost to you for using
PayPal)
Click Here >>>PayPal
I also accept Dwolla payments.
GO TO: HOME PAGE (Index)